Electric Water Pump EWP150 BLACK (ALLOY) KIT (Part #8065) (12V) (Davies Craig)

ELECTRIC WATER PUMP - EWP150 BLACK (ALLOY) (PART #8060) (12V). Celebrating 50 years, Davies Craig Pty Ltd has launched a. 150 Remote-Mounted Electric Water Pump!

This attractive model is supplied in glorious matt black power-coat and offers all the modern performance, compactness, and style you come to expect with the high-quality engine cooling products offered by Davies, Craig Pty Ltd. Kit (Part #8065) This Listing. Combo with Controller (Part #8975). Muscle up your engine cooling system with the Davies Craig. 150 alloy Electric Water Pump.

Like all EWPs, this advanced unit is designed for remote mounting in the engine bay to satisfy those higher horsepower, turbocharged, supercharged and'worked' engines which develop excessive heat &. 150 alloy unit is manufactured with -AN16 (12) internal inlet and outlet fittings for neat, tight screw-in fitting applications. This rugged alloy hi-flow electric water pump is designed to complement or replace the engine's existing mechanical water pump. This essential performance accessory increases power to your vehicle's drive wheels and improves coolant temperature control.

RED - 6mm Ring Termina. RELAY - 12V 40 Amp 5 Pin W/- Resistor Protection. SCREW - SELF TAP 8X3/8 BZ. 3V DC to 15V DC.

40° to 120°C (-40° to 248°F). 1,170 grams (2.6 lb). 500 kPa (72.5 psi).

No, none of our pumps are self-priming. 35mm to 51mm (1.38" to 2"). EWP Inlet & Outlet 38mm. With 3mm Sleeve (#8510) 44mm.

With 6mm Sleeve (#8511) 51mm. Inlet & Outlet: -16AN (12). The Digital Controller will vary the speed of the EWP. In response to the engine's coolant temperature.

Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating'heat soak' and extending engine life.

150 Digital Controller Combo is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle's engine, including an easy-to-follow DIY instruction booklet. The world's most advanced total engine cooling management system. Leaving the mechanical water pump in place, install the EWP. Into the bottom radiator hose. Remove the thermostat and drill two approx.

3mm (1/8) holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required. INSTALLATION - disabling Mechanical water pump. You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation. If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8) holes in the thermostat plate to allow some coolant circulation. In both these cases, the EWP. Will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended). Remove the mechanical water pump and remove the thermostat.

Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt. Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks. Removed mechanical water pump (Ideal). Remove the mechanical water pump and thermostat from the engine.

Install a Davies Craig EWP. Header Adaptor or blanking plate (not supplied).

Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks. This method will require you to modify or replace the standard radiator hose. Install an appropriate length belt (not supplied) to drive the accessories.

Will be adequately supported by the radiator hose. Where mounting is required, the EWP. Must be soft mounted to protect against vibration. 150 Part #8700 or #8710 Mounting bracket is recommended. Engines up to 2.0L.

Engines up to 2.0L - 3.5L. Engines up to 3.5L - 5.0L. Engines 5.0L or greater. Off Road, Drifting & Speedway.